ELB90 1/4 TUBE X 1/4 MPT PLASTIC

4.35

Quantity
Part no. 0204020869 Categories: ,

Description

ELB90 1/4 TUBE X 1/4 MPT PLASTIC

Part No. 0204020869

 

Overview

MULTI MEDIA FILTER PLUMBING ASSY  B075000001

Multi Media Filter contains a media filter bed (gravel and sand). The media traps suspended solids larger than 30 micron. The Multi Media Filter is back washable.

  • Multi Media Filter (optional) is supplied pre-mounted to its own base.
  • Mount the Multi Media Filter base onto a flat horizontal surface and secure the base in place using the supplied mounting hardware.
  • Mount the assembly below water level to minimize feed pressure loss.
  • Connect the inlet to the Booster Pump Outlet or Fresh Water Flush Outlet.
  • Connect the Outlet to the Commercial Prefilter Inlet.
  • Connect the Media Filter Waste Discharge Fitting to the Over Board Dump Waste Fitting.
  • Unscrew the Multi Media Fill Plug, located on top of the Multi Media Filter Lid.
  • Place a funnel over the Fill Hole.
  • Pour into the funnel approximately 15 lbs (7 kg) of small gravel (1/8 x 1/4 inch) first (on the bottom) then approximately 26 lbs (12 kg) of #20 silica sand last (on top of the small gravel).
  • Remove the funnel and clean the Fill Plug female threads.
  • Screw the Fill Plug back onto the Lid and tighten lightly with a wrench.
  • Note this Fill Plug is O-ring sealed and requires only light tightening to seal the O-ring.
  • Backwash Multi-Media Filter before operating the system.

 

PREFILTER ASSY W/GAUGE HORIZON SEAFARI  H2108200002

Standard 25 to 5 micron Pre-Filters consists of two filter housings connected in series with each other. The filter elements remove suspended solids from the System Feed Water. The first Pre-filter contains a filter element, which filters the feed water to 25 micron. The second Pre-filter contains a finer element, which filters the feed water to 5 micron.

  • Must be mounted against a flat vertical surface using the supplied hardware.
  • It is preferable to mount the Standard Pre-filters in a straight line with and in close proximity to the Booster Pump.
  • Allow minimum 4″ below the bottom of the bowl for Pre-filter Element removal.
  • Connect the Booster Pump Outlet (or Plankton Filter Outlet if used or Multi Media Filter Outlet if used) to the Pre-filter Inlet.
  • If the Oil/Water Separator is not used then connect the Standard Pre-filters Outlet to the High Pressure Pump Inlet.

OIL WATER SEPARATOR 32.5 SQ FT HORIZON SEAFARI B111800006 

Oil/Water Separator Filter The separator element separates oil and suspended solids from the System Feed Water. Oil permanently destroys the R.O. Membrane Element, therefore, it is recommended that the user avoid operating the Horizon Seafari in oily, polluted waters.

  • Follows the Commercial Pre-filter.
  • The Oil/Water Separator Assembly is plumbed for water flow in the opposite direction as the Pre-filter.
  • Using the supplied ¾” hose, connect the Oil/Water Separator Inlet to the Standard or Commercial Pre-filter Outlet.
  • Connect the Oil/Water Separator Outlet to the High Pressure Pump Inlet.
  • NOTE:
    • The Oil/Water Separator utilizes the same filter housing as the Commercial Prefilter.
    • However, the Oil/Water Separator is plumbed opposite of (backwards from) the Commercial Prefilter.
    • The standard filter housings have raised arrows and lettering molded indicating correct flow for the Commercial Prefilter.
    • These markings are INCORRECT for the Oil/Water Separator.
    • The OIl/Water Separator’s correct water flow enters the center core of the filter element and migrates to the outer surface of the filter element.

Downloads

AVAILABLE TUBES AND FITTINGS – ELBOW 90 MALE
AVAILABLE FITTINGS

OIL WATER SEPARATOR 32.5 SQ FT HORIZON SEAFARI B111800006
EXPLODED PARTS VIEW